You are here Home Technical Resource Environment
RoHS Compliance
Current Options for RoHS Compliance at Harwin
The chart below is an overview of each product range and its RoHS and Non-RoHS options. For exact information on a product, please contact Harwin on leadfree@harwin.co.uk. Scroll down to see a summary of Finish codes used in Harwin part numbers.
Please note, our Hand tooling is not affected by the RoHS and WEEE legislations, as it is not electrical equipment.
 RoHS Compliant product |
 Product maintained in previous Non-RoHS Compliant format |
|---|---|
| Fine Pitch connectors: 0.5mm pitch (M402) Connectors 0.80mm pitch (M60) Connectors 1.00m pitch (M40) Connectors 1.25mm (M30) Connectors |
|
| 1.27mm pitch (M50, M52) Connectors | |
| 2.00mm pitch (M22) Connectors | |
| 2.54mm pitch (M20) Connectors | |
| PC/104 and PC/104 Plus Connectors | |
| FPC Connectors | |
| HotShoe Connectors | |
| Commercial MIL-C-5015 | |
| I/O Connectors | |
| Memory Card Connectors | |
| MMCX Coax Connectors | |
 |
|
 |
|
 |
|
 |
|
| RFI Shield Clips | RFI Shield Clips |
| RFI Shield Fingers | |
| SMT Test Point | SMT Test Point |
| SMT Jumper Links | SMT Jumper Links |
| SMT Fuse Clip | SMT Fuse Clip |
| SMT Cable Clips | |
| Tab Terminals | |
| Terminals & Turrets (turned) | |
| PCB Sockets | |
| Metal & Plastic Spacers (starting R) | |
| Ø1.00mm Shorting Links (D308X) | Uninsulated Shorting Links |
| IC Sockets, Headers & strips | |
| PLCC Sockets | |
| Track Pins | |
| 2&3-way Power Conn. (K3XXX-XX) | |
| Spring Probes |
Finish Codes
Finish codes are normally located as the last two numbers within a Harwin Part number, although occasionally (such as Datamate Mix-Tek), they maybe located elsewhere within the part number.
RoHS Compliant finish codes that were allocated at the beginning of the RoHS compliance project guarantee that the item is both fully RoHS compliant, and use high-temperature plastics where applicable. These finish codes are:
- 42 = Gold on contact area, 100% Tin on Tails
- 45 = Gold
- 46 = 100% Tin
Previous, historical, finish codes are more varied, and the same code may have different meanings depending on the product range being considered. Some may be compliant, and some may not. To be certain of the finish, please consult the applicable technical drawing, or e-mail technical@harwin. Here is a summary of typical codes used:
- 00 = Unspecified colour (plastics) or unplated
- 01 = 100% Tin (Terminals, H2XXX, some H3XXXX, H9XXX)
= Tin/Lead (Shorting Links D308X-01)
= Gold Clip, 100% Tin shell (PCB Loose Sockets, H3XXX)
= Gold Clip, Tin/Lead shell (Datamate Female) - 02 = Nickel
- 05 = Gold (RoHS Compliant, but not always High Temperature, check drawing)
- 06 = Tin/Lead
- T6 = Tin/Lead
- 22 = Gold on contact area, Tin/Lead on tails
- 87 to 99 = Plastic colour, see drawing for metal finish and colour
Copyright Harwin Plc 2004-2013. Harwin Plc Registered in England No. 509831